Black Templar Initiates and Base Recipe

Black Armor

- Base coat VMS Hull Red

- Stipple VMS 70.982 Cavalry Brown

- Stipple Black. Used standard GW Chaos Black, for these

- Stipple GW Layer Dark Reaper

- Stipple GW Space Wolves Gray

- Stipple GW Base Leadbelcher

- Wash with 1:1 Agrax Earth : Nuln Oil

- Edge highlight metallic silver

Boots / Gloves / Belts / Pouches

- Base coat VMS 70.872 Chocolate Brown

- Wash with 1:1 Agrax Earth : Nuln Oil

- Highlight with VMS 70.872 Chocolate Brown

- Highlight with VMS 70.872 with a touch of Ivory

Pants

- Base with GW Base XV-88

- Wash with GW Contrast Skeleton Horde

- Highlight with XV-88. Mostly stippling the highlights back on

Tabard

- Base with GW Base Hobgrot

- Wash with GW Contrast Skeleton Horde

- Highlight with GW Base Hobgrot

- Highlight with GW Ushabti Bone

- Highlight with GW Screaming Skull

Highlights were done with a mix of regular lines and stippling. Stippling was mostly on the screaming skull and ushabti highlights

Shoulder Pads

- Base with GW Base Ionarch Skin with heavy stippling

- Light stippling of VMS Hull Red

- Base crosses black

- Clean up with Ionarch Skin

- Stipple GW Layer Deepkin Flesh

Weapons

- Stipple on GW Base Mephiston Red

- Stipple on GW Layer Evil Suns Scarlet

- Stipple on GW Base Ironbelcher

-Base Ironbelcher rest of weapon

- Wash with 1:1 Agrax Earth : Nuln Oil

- Highlight with silver

Comments

15mm/6mm Woods (WIP)

Good bye to green felt templates! I ended up with a scrap piece of 1/4" ply wood from some home remodeling. And while I had an urge to do some buildings for 15mm, I haven't been playing a lot of 15mm gaming lately. So, I decided that some woods would work for both 6mm (Dirtside 2 and Strike Legion) as well as 15mm sci fi or 15mm anceints gaming (ADG). I started by: Sketching out some rough circular shapes on the 1/4" ply Cutting them out with a jig saw. I didn't follow the lines exactly, just tried to keep near them Power sanded down the edges to give them a bit of a gradual slope Glued 3"(For 15mm) or 2" (for 6mm) around the edges, with one or two in the middle for support. I mostly left them open as these are for gaming, not for display. I need to fit the figures in there! This was done with liquid nails. I put about a pea worth of liquid nails down, pushed the nail in and gave it a bit of a twirl. Left me with the foll...

Heresy Hellmites

80 Skaven clan rats have been painted up, only awaiting the dozens of fellow to make up the rest of the army... To take a break I did a quick paint job on Heresy's Hellmites: Nothing fancy, just a three color dry bush to get them up and off the table. Lovely little sculpts, but I think I mismatched some of the backs to bodies. Colors: Body: Base GW Chardonite Granite, Wash Black, Highlight Graveyard earth Beaks: Base Tausept Ochre, Wash Black, Highlight Graveyard Earth Sack: Base VMC Hull Red, Wash GW Badab Black, Highlight Dark Flesh, Highlight Blood Red, Wash Ogryn Flesh Base: Mushroom, Wash Raw Umber, Drybrush Mushroom, Drybrush Butter Pecan, Drybrush Vintage White. Army Painter 4mm/6mm grass tufts.

Skaven Test Pack Masters

Bit happier with the white one, but like the dirt on the red one a bit better. In the end, went with neither of these two designs.

Fear The Squirrels

Search This Blog